Search results

Hi folks. Long time formula owner here that sold my boat (41 PC) about a month ago. Long story short and a few bad deals, I've put an offer in on a 2005 Formula 48. The boat is equipped with Cummings QSM-11 660 diesels. Couple of questions for those with similar boats: * What kind of...

As much as I hate doing so, I am selling my 2000 Formula 41 PC as we are moving up. She has twin 8.2L MPI Mercruisers with approx 350 hours All maintenance recently performed for this season * Spark plugs - both engines replaced * New impellers - both engines * New serpentine belts - both...

Anyone happen to know the part # for replacement metal basket for a/c strainers? they are approx 6" long and not sure about diameter.... maybe 2 1/2"? Any help would be greatly apprecaited.

Ok gotcha! I wouldn't post up porn. Just finished getting boat ready to go for this season. Here she is nice and clean. Turned out pretty good for a 20 year old boat.

Anyone here know off-hand what size the A/C strainers are for the 41PC? Thanks!

Hi folks. The handle on my shower finally gave up the ghost and appears to be glued on the plastic. Anyone else had this happen and if so, how did you fix it? I tried Gorilla glue but that didn't work. Thanks!

For 41 PC owners. Right behind the generator is the bilge pump. There are two big bolts coming through at the top before the tunnel (where the bilge pump goes down near the bottom). Is that for one of the zinc plates? Thanks in advance.

Was beautiful out so I de-winterized the boat. Both engines started up on first try as did the generator. Went ahead and changed the fuel filters. Next up --- changing the trans fluid and going to dewinterize the water system.

Hi folks. The back seat on my boat (41 PC) sorta hides away into the trunk. The vinyl around the banjo bolt is worn and it looks like the vinyl is wearing away. Anyone had to replace this? If so, what size vinyl did you use? Looks like the seat itself is bolted down across a piece of...

Anyone here know how to remove the shower box on the 41 PC?

Hi folks. I'm back to wrenching on my boat quite a bit and wanted to throw out a question. * Why do our boats have the float switch and bilge pumps separately? Is it a symptom of technology evolution (pumps back in the day didn't have the float switch automatically built in?) or is it...

On the bow where the anchor chain comes up there is a rubber piece that the chain goes up and down on and I can't think of the name of it. I need to replace it because it's worn down from all the up/down anchoring over the years. Bow roller?

Just curious how much water you typically see in your bilge at any one time? Does your bilge pump push water out frequently? Have you vacuumed your bilge out and then you see water back in? Just wondering if anyone actually has a completely "DRY" bilge?

Does anyone have any idea what formula used to sorta make a seal around the cabin door? It looks like a felt type seal with plastic ..... Anyone have any ideas? Sent from my iPhone using Tapatalk

On the sunpads up front, has anyone here converted your sunpads to make them sit up? If so, how did you do it? Is there some type of conversion kit?

The forward berth hatch screen is a bit bent and need to replace. Anyone happen to know what size I need there? Thanks!

New speakers installed on the arch. Old ones were shot.

Has anyone else had their hot water heater leaking from the bottom? I feel like I have to replace it but it looks like I have to remove the generator to do so because of the way it's mounted :-(. Any suggestions?

The gold striping on one side has faded away on about a 1 foot X 1 foot area. Where can I get new gold striping? Any special striping required?

Somehow and some way, the stove on my boat simply fell down into the hole. Does anyone here know how you're supposed to "set" the burners on the stove? Have the 3 burner stove model # as well? thanks!